SilverStone SST-TJ08-E Especificaciones

NO: G11214080May, 2011TJ08-EAdvanced Micro-ATX tower chassis withbreakthrough storage and cooling capacity

lnstallation Guide8Reinstall the assembled motherboard tray back into the chassis. If you have either the ATX12V 4pin or EPS 8pin cables connected, p

lnstallation Guide9На этом этапе рекомендуется начать прокладку кабелей и подсоединить кабели, например кабель ATX с 24-контактным разъемом, разъемы в

lnstallation Guide10Проложите все кабели питания через отверстие слева от блока питания. Неиспользуемые кабели можно хранить в дополнительном отсеке с

lnstallation Guide11Remove the external 3.5” drive bay cover to install an external 3.5” device. If you need to install a 3.5” hard drive into this s

lnstallation Guide1213Remove the 5.25” drive bay covers to install required 5.25” devices.Снимите крыши отсеков для 5,25-дюймовых устройств и установи

lnstallation Guide1415Install 3.5” hard drives into the drive cage.Установите 3,5-дюймовые жесткие диски в кронштейн для жестких дисков.將3.5”硬碟安裝至硬碟架。

lnstallation Guide1617Remove expansion slot covers to install required expansion cards. Unused slots should have covers installed.Снимите крышки слот

lnstallation Guide18Reinstall both left and right side panel to complete installation.Для завершения установки установите на место левую и правую боко

Connector Definition(1) Front panel connector installationPOWER SWITCH RESET SWITCHPower switch and reset switch installation guide:Please refer to th

Connector Definition(1) Front panel connector installationLED connector installation guide：Please refer to the motherboard manuals for the motherboard

SpecificationsDisassemble ChartInstallation guideFront panel connector guideFront I/O connector guideComponent size limitationsRecommended cooling dev

Connector Definition(2) Front I/O connector installationBelow are the front I/O connectors pin definition, please also check your motherboard manual t

Component Size Limitations(1) CPU cooler height limitationThe height limit is 165mm and there is 18mm of clearance around the motherboard’s top edge.T

Component Size Limitations(1) CPU cooler height limitationМаксимальная высота кулера – 165 мм, и зазор вокруг верхнего края материнской платы должен с

Component Size Limitations(2) Power supply and optical drive limitationA: Length limitationThe Total length for power supply and optical drive:Power s

Component Size Limitations(2) Power supply and optical drive limitationThe photo illustrate a 180mm long power supply (SilverStone ST1200-G) and a 170

Component Size Limitations(2) Power supply and optical drive limitationНа фотографии показаны установленные в корпус TJ08-E блок питания длиной 180 мм

Component Size Limitations(2) Power supply and optical drive limitationThe absolute maximum length for optical drive is 220mm. Once the optical drive

Component Size Limitations(2) Power supply and optical drive limitationB: Power supply cable length recommendations:B: Netzteilkabel – Längenempfehlun

Component Size Limitations(3) Graphics card/expansion card length limitationFirst and second slots support 13.25” long cardsThird and fourth slots sup

Component Size Limitations(4) Memory height limitationThere is 54mm of distance between the motherboard to the hard drive. If you use a memory simila

Aluminum front panel, steel bodyMicro ATX, Mini-DTX, Mini-ITXFrontSST-TJ08B-E (black)(backwards compatible with 140mm fan)Rear1 x 120mm fan slot (opti

CPU Cooler Supporter12First set the chassis on its side, make sure it is on a level surface.Сначала положите корпус набок на ровную поверхность.請先翻倒機殼

CPU Supporter3CPU Cooler SupporterЕсли положение опоры не соответствует необходимой конфигурации, для перемещения опоры отвинтите еще два винта слева

CPU Cooler Supporter45Move the supporter arm up to touch the installed CPU cooler and then secure the middle screw.Переместите рычаг опоры вверх до со

CPU Cooler Supporter6Recommended usage range for supporter:From 18mm beyond edge of the motherboard to 30mm inward from the motherboard edge. Most 12

CPU SupporterGraphics Card SupporterA plastic block supporter located above the hard drive cage will support the backside of the graphics card install

Graphics Card SupporterIf the graphics card you use does not have a backplate, please adhere the included foam pad onto the plastic block supporter to

Optimal Thermal Performance Layout如果您使用塔型散熱器，我們建議您將散熱器安裝方向為風扇往後吹的方式，以順著TJ08-E的散熱風流。如果您使用塔型散热器，我们建议您将散热器安装方向为风扇往後吹的方式，以顺着TJ08-E的散热风流。Please do not remo

Optimal Thermal Performance LayoutWhen choosing a graphics card, we recommend models that have fan blowing exhaust air to the rear slot, this will ens

Tips For Cable ManagementABThere are plenty of cable tie bridges behind the motherboard tray, which you can utilize to organize cables.За кронштейном

CPU SupporterTips For Cable ManagementCЗазор между передним краем кронштейна материнской платы и левой боковой панелью составляет менее 10 мм. Зазор м

PICTURE ITEM PURPOSESCREW A SECURE MOTHERBOARDSCREW BSECURE POWER SUPPLY OR 3.5" HARD DRIVE AND MOTHERBOARDSCREW C SECURE OPTICAL DRIVEBUNCH WIRE

Fan Speed AdjustmentHLTJ08-E’s one main Air Penetrator AP181 fan are speed adjustable in two speeds, 700rpm or 1200rpm.The speeds are designed for sil

Fan ReplacementSilverStone also has three models of 180mm for sale separately for replacement or upgrade,If downgrade of airflow is required, the fron

Upgrade And MaintenanceTJ08-E’s positive air pressure design is an effective configuration that will reduce dust buildup inside the case. Small air p

CPU SupporterUpgrade And Maintenance(1) Fan filter removal guide1The front filter can be removed from either right or left side. To remove, poke on o

Upgrade And Maintenance(2) ClearCMOSClearCMOS with Expansion Slot BracketClearCMOS without Expansion Slot Bracket TJ08-E Rear view photoInstall Positi

Upgrade And Maintenance(3) 180mm fan removal guide1Remove both right and left side panelsСнимите левую и правую боковые панели.已經拆卸左右板的狀態已经拆卸左右板的状态左右の

Upgrade And Maintenance(3) 180mm fan removal guide3Remove main drive cage Извлеките основной кронштейн для жестких дисков.請移除主要硬碟架请移除主要硬盘架メインのドライブケージを

Upgrade And Maintenance(3) 180mm fan removal guide5Loosen screws holding the fan speed switch, then route the switch through the small hole to the rig

Upgrade And Maintenance(3) 180mm fan removal guide7To reinstall the fan, simply follow the steps in reverse, when reinstalling fan speed switch, make

Protect Your ComputerKensington Security SlotВ продаже имеются замки и тросы, используемые с разъемами для защитных замков защитного замка Kensington,

USB 3.0 CONNETORHD AUDIO CONNETORFRONT I/O ( USB 3.0 x 2 / audio x 1 / MIC x 1 )4

Questions and Answers(1) Tower CoolerВопрос: При наличии процессорного кулера башенного типа можно ли обойтись без установки процессорного вентилятора

Questions and Answers(2) 3.5” Drive BayВ.Как извлечь жесткий диск, установленный в самом нижнем отсеке для внешних 3,5-дюймовых устройств, если матери

Before you begin, please make sure that you (1) have all components collected.(2) check that all components do not have compatibility problems with ea

lnstallation Guide3Loosen three screws holding the motherboard tray to remove it.Отвинтите три винта, крепящих кронштейн материнской платы, и снимите

lnstallation Guide5Install 2.5” drive into the bottom of the chassis and secure with screws.Установите 2,5-дюймовый жесткий диск в нижнюю часть корпус

lnstallation Guide7Install motherboard onto the motherboard tray. If you have already installed a large CPU cooler on the motherboard, we recommend c