SilverStone SG06-LITE Guía de instalación

SG06LITEThe golden standard of Mini-ITX cases

Install your slim optical drive onto the bracket and secure with included screws. Установите тонкий оптический привод в кронштейн и закрепите прилагае

9Reinstall the optical drive bracket into the chassis and secure with screws Установите кронштейн оптического привода в корпус и закрепите его шуруп

Please remove the screws holding the expansion card slot cover, and remove it. Открутите шурупы на крышке слота карты расширения и снимите крышку.

11Reinstall the expansion card slot cover and secure with screws. Поместите на место крышку слота карты расширения и закрепите ее шурупами. Install

Attach the rubber standoff onto the chassis appropriately as required. Прикрепите к корпусу резиновые опоры. Befestigen Sie den Gummi-Abstandhalte

(1) Front panel connector installationPower switch and reset switch installation guide:Please refer to the motherboard manuals for the motherboard’s “

Connector definitionPlease refer to the motherboard manuals for the motherboard’s “Front Panel Connector ” or “System Panel Connector” pin definition.

Front I/O connector guideBelow are the front I/O connectors pin definition, please also check your motherboard manual to cross reference with motherbo

Component size limitationsAlthough the SG06-Lite is small, it is still compatible with many oversized components, please refer to the following guidel

Component size limitations (2) PSU limitationSG06-Lite는 100mm 깊이의 표준 SFX 전원 공급장치를 지원합니다.SG06-Liteは標準SFX電源（100㎜深)に対応しています。The SG06-Lite supports stand

Component size limitations (3) Graphics card/expansion card length limitationSG06-Lite은 최대 10”(254mm)의 그래픽 카드를 지원합니다.Graphic card length reference:NV

Component size limitations (4) Optical drive limitationSG06-Lite는 12.7mm 두께의 슬림형 광드라이브만 수용합니다. 아래는 두께가 12.7mm인 광드라이브의 예입니다.SG06-Liteには、12.7mm厚スリム光学ドライ

Upgrade and Maintenance(1) Fan filter removal guideSG06-Lite의 양압 디자인은 케이스 내부에 먼지가 싸이는 것을 방지 하기 위한 효과적인 디자인입니다. 작은 분진나이 먼지는 케이스 내부에 있는 필터에 시간에 따라 쌓이게 됩

Please remove the screws holding the top cover with a screw driver, then pull ittoward the back to lift it outward away from the chassis. С помощью от

Remove the fan filter Снимите фильтр вентилятора. Entfernen Sie den Lüfterfilter.Enlever le filtre du ventilateur.Retire el filtro del ventilador.R

Warranty InformationThis product has a limited 1 year warranty in North America and Australia. For information on warranty periods in other regions,

G11218750February

SST-SG06BB-LITESST-SG06S-LITEAluminum front panel, steel bodyMini-DTX, Mini-ITX12.7mm slim optical drive x 1 3.5” x 1 , 2.5” x 1 1 x 120mm intake fan

TOP COVEREXPANSION SLOT X2MOTHERBOARD (NOT INCLUDED)FILTERFRONT PANEL12025 FAN3.5” HDD TRAY2.5” HDD BAY (NOT INCLUDED)SLIM OPTICAL DRIVE TRAYSLIM OPTI

3Please remove the screws holding the top cover with a screw driver, then pull it toward the back to lift it outward away from the chassis.С помощью о

Remove the screws holding the hard drive bracket with a screw driver as shown, then remove the cage outward from the chassis. С помощью отвертки откру

5Press the area as shown to release the clips, then remove the front panel. Нажмите на указанные зажимы и снимите переднюю панель. Drücken Sie auf

Remove the tab of optical drive bay with a screw driver. С помощью отвертки уберите накладку отсека для оптического привода. Entfernen Sie Klappe

7Install your motherboard into the chassis as shown and secure with included screws. Установите материнскую плату в корпус и закрепите ее прилагаемыми